--- title: Edge gateway outdoor type description: This chapter describes the installation … url: "https://manual.amnimo.com/docs/edge-gateway-outdoor-type/edge-gateway-outdoor-type/" updated: "2024-07-19" category: 屋外タイプ設置ガイド / AIエッジゲートウェイ 屋外版 / エッジゲートウェイ 屋外版（屋外タイプ設置ガイド） --- # Edge gateway outdoor type This chapter describes the installation procedure for the Edge Gateway Outdoor Type (AG20). ## Outline Drawing - Weight: approx. 2.8 kg ![](https://manual.amnimo.com/wp-content/uploads/2024/06/image009-1024x724.png) ## About power supply connection ![](https://manual.amnimo.com/wp-content/uploads/2024/06/image010-1024x634.png) **Memo** - For power supply connection, connect 100 VAC (L side and N side) and FG (frame ground) as shown above. - The FG mark and the L side are clearly marked near the connector. - FG must be connected. Failure to do so may cause accidents or malfunctions. - Please be very careful not to touch these terminals with metal or your body by mistake. - After connecting the power supply, work in such a way that the power supply to the equipment can be cut off by installing an NFB (wiring circuit breaker) on the AC100V power line. - After connecting the power supply, attach terminal caps to the terminal block. ## When using a cable gland ### necessities | Cable gland (recommended)\* sold separately | | --- | | M7901YR (FGB21L-14B) \* For power cable [https://www.ip68.jp/products/210_2010_b_products.html](https://www.ip68.jp/products/210_2010_b_products.html) | | M7901YQ (FGA21L-10B-SD) \* For Ether cable [https://www.ip68.jp/products/210_2015_products.html](https://www.ip68.jp/products/210_2015_products.html) | | M7901YY (FGA21L-06B-SD) \* For Ether cable [https://www.ip68.jp/products/210_2015_products.html](https://www.ip68.jp/products/210_2015_products.html) | | M7901YZ (FGA21L-H2-06B-SD) \* For Ether cable (when 2 cables are used) [https://www.ip68.jp/products/210_8010_products.html](https://www.ip68.jp/products/210_8010_products.html) | ### Installation Instructions Remove the grommet. ![](https://manual.amnimo.com/wp-content/uploads/2024/06/image012.png) Use the body and washers from the outside of the outdoor box and the lock nut from the inside of the outdoor box in the holes where the grommets were removed, clamp the box and tighten with the specified torque (reference value of tightening torque: 2.2 to 3.0 N・m). ![](https://manual.amnimo.com/wp-content/uploads/2024/06/image013.png) Pass the power cable and LAN cable through the cable gland. **Memo** - To run two Ether cables through one cable gland, use a cable gland for two ports. - It is not possible to pull out all wiring using only the standard holes. Additional hole fabrication may be required, so please contact your Amnimo sales representative before purchasing. - Use LAN cables with compatible wire diameters. See [Accessories (sold separately)](https://manual.amnimo.com/docs/outdoor-type-installation-guide/accessary/%e3%82%a2%e3%82%af%e3%82%bb%e3%82%b5%e3%83%aa%ef%bc%88%e5%88%a5%e5%a3%b2%e5%93%81%ef%bc%89/). - When using a cable with RJ-45, use a connector diameter of 14 mm or smaller. - When using connectors larger than 14 mm, crimp the connectors after passing through the cable gland. ![](https://manual.amnimo.com/wp-content/uploads/2024/06/image014.png) Wiring process. See [Internal Wiring and Wiring Handling](https://manual.amnimo.com/en/docs/outdoor-type-installation-guide/edge-gateway-outdoor-type/edge-gateway-outdoor-type/#%E5%86%85%E9%83%A8%E7%B5%90%E7%B7%9A%E3%81%A8%E9%85%8D%E7%B7%9A%E5%87%A6%E7%90%86). After cable connection and excess length treatment, tighten the sealing nut of the cable gland with the specified torque (reference value of tightening torque: 1.8 to 2.5 N-m). ![](https://manual.amnimo.com/wp-content/uploads/2024/06/image015.png) ## When using PF pipe connectors ### necessities | PF pipe connector with verified connection \* Not sold by Amnimo | | --- | | Furukawa Electric: PFS-16KSR-I (IPX5 compliant product) [https://www.furukawa.co.jp/eflex/product/plafleky/p_pfbkr.htm](https://www.furukawa.co.jp/eflex/product/plafleky/p_pfbkr.htm) | | Miraikogio: FPK16YPS (IPX7 compliant product) [https://www.mirai.co.jp/densetu/pdf-catalog_2021/6000221.pdf](https://www.mirai.co.jp/densetu/pdf-catalog_2021/6000221.pdf) | ### Installation Instructions Remove the grommet. ![](https://manual.amnimo.com/wp-content/uploads/2024/06/image012-1024x563.png) Use the body and washers from the outside and the lock nuts from the inside in the holes where the grommets were removed, and tighten and secure the box firmly with torque between them. **Memo** There is no manufacturer's recommended tightening torque for both PF pipe connectors. ![](https://manual.amnimo.com/wp-content/uploads/2024/06/image016.png) Pass the power cable and LAN cable through the PF tube and connect them to the PF tube connector. **Memo** It is not possible to pull out all the wires using only the standard holes. Additional hole machining may be required, so please consult your Amnimo sales representative prior to purchase. ![](https://manual.amnimo.com/wp-content/uploads/2024/06/image017.png) Wiring process. See [Internal Wiring and Wiring Handling](https://manual.amnimo.com/en/docs/outdoor-type-installation-guide/edge-gateway-outdoor-type/edge-gateway-outdoor-type/#%E5%86%85%E9%83%A8%E7%B5%90%E7%B7%9A%E3%81%A8%E9%85%8D%E7%B7%9A%E5%87%A6%E7%90%86). ## Internal wiring and wiring treatment ### necessities | Cable ties for fixing cables (2 pcs. included) \*If you need more, please procure and use the following model number. | | --- | | (Recommended) Takeuchi Kogyo Reuse Snapping Ties RST-130V0 | ### Wire connection example Since cables are not fixed when using PF Suga, the following procedure can be used to fix cables to prevent stress on connectors and terminal blocks. The six cable clamp fixing holes shown below are provided so that the cable clamps can be fixed by inserting the cable ties included with the product. ![](https://manual.amnimo.com/wp-content/uploads/2024/06/image018.png) Connect the power and LAN cables and adjust their lengths with cable clamps. ![](https://manual.amnimo.com/wp-content/uploads/2024/06/image019-768x1024.jpg) ## About wall installation ### necessities | Wall mounting bracket (recommended) \* Sold separately | | --- | | M7901YX (CK-26P) [https://www.takachi-el.co.jp/products/CK_BCAP](https://www.takachi-el.co.jp/products/CK_BCAP) | ### Mounting example When installing on a wall, use appropriate bolts or screws that can withstand the weight of the unit against a sufficiently strong wall surface. When attaching the metal fittings to the box, use a tightening torque of 1.0 N-m as a guide for installation. ![](https://manual.amnimo.com/wp-content/uploads/2024/06/image020.png) ## Pole Installation ### necessities | Pole mounting bracket (recommended) \* Compatible pole/con pillar diameter: 60 to 400 mm M7901YW (SSK-200) [https://www.takachi-el.co.jp/products/SSK_BCAP](https://www.takachi-el.co.jp/products/SSK_BCAP) | | --- | | Pole mounting band (recommended) \* Pole/con pillar diameter: 60 to 400 mm M7901YU (PKB-10S) [https://www.takachi-el.co.jp/products/PKB](https://www.takachi-el.co.jp/products/PKB) | ### Mounting example When attaching metal fittings to the box, use a tightening torque of 1.0 N-m as a guide for installation. ![](https://manual.amnimo.com/wp-content/uploads/2024/06/image021.png) Please refer to the following page from the manufacturer for belt installation instructions. [https://www.takachi-el.co.jp/assets/attachments/images/PKB10S_PKB20S_manual.pdf](https://www.takachi-el.co.jp/assets/attachments/images/PKB10S_PKB20S_manual.pdf)