---
title: Names and roles of the various parts of the Edge Gateway
description: This section describes the basic configu…
url: "https://manual.amnimo.com/docs/edge-gateway-product-overview-ag-individual-guide/names-and-roles-of-the-various-parts-of-the-edge-gateway/"
updated: "2024-09-05"
category: AG個別 / エッジゲートウェイの製品概要（AG個別ガイド）
---

# Names and roles of the various parts of the Edge Gateway

This section describes the basic configuration of the Edge Gateway main unit.

### Edge gateway (indoor version)

This section describes the basic configuration of the main unit of the Edge Gateway (indoor version).

#### facade

The configuration of the front panel (with the lid of the SD card section open) is shown below.

![](https://manual.amnimo.com/wp-content/uploads/2024/08/画像8-1024x372.png)

| No. | name | Description. |
| --- | --- | --- |
| ❶ | LED Indicator | PWR: Displays the power supply status. ANT: Displays the antenna status. MOB: Shows the line connection status of the communication module. ST1, ST2, and ST3: Specific states are displayed in combination with other indicators. |
| ❷ | CONSOLE Port | Used to configure the edge gateway. |
| ❸ | USB port | Operates as a USB 2.0 host. |
| ❹ | DIP switches for configuration | Sets the startup mode of the edge gateway. |
| (in Japanese) ❺ | PUSH switch | Used to shut down the Edge Gateway or restore it to factory settings. |
| (in Japanese) ❻ | SD card slot | SDXC type, UHS-I compatible. |

#### back

The rear configuration is shown below.

![](https://manual.amnimo.com/wp-content/uploads/2024/08/画像4-1024x410.png)

| No. | name | Description. |
| --- | --- | --- |
| ❶ | subantenna | Connect antenna for 3G/4G line, SMA-J type. |
| ❷ | GPS antenna terminal | Connect GNSS antenna, SMA-J type. |
| ❸ | D OUT | Isolated type digital output terminal for connection to external devices. |
| ❹ | D IN | Isolated type digital input terminal for connection to external devices. |
| (in Japanese) ❺ | SIM card slot 0, SIM card slot 1 | Two SIM cards can be inserted in the SIM card slot. The priority level changes depending on the setting. By default, SIM 0 is used. |
| (in Japanese) ❻ | main antenna | Connect antenna for 3G/4G line, SMA-J type. |
| ❼ | RS-232 port | Compatible with D-Sub 9-pin connectors. |
| (in Japanese) ❽ | ETH0 port | Standard Ethernet port with Gigabit Ethernet support. |
| (in Japanese) ❾ | LAN0, LAN1, LAN2, LAN3 ports (4-port switch) | Standard Ethernet port with Gigabit Ethernet support, PoE (IEEE802.3at) compliant and PoE power supply. |
| ❿ | FG | Connect frame ground. |
| ⓫ | PWR | Connect the supplied dedicated power supply AC adapter. |

#### three-sided view

A three-view diagram is shown below.
The nameplate label uses AG10-030GA-10 as an example.

![](https://manual.amnimo.com/wp-content/uploads/2024/08/image-3.png)

### Edge gateway (outdoor version)

This section describes the basic configuration of the main unit of the Edge Gateway (outdoor version).

#### Front (lid open)

The configuration of the front view when the lid is open (with the lid of the SD card section opened) is shown below.

![](https://manual.amnimo.com/wp-content/uploads/2024/08/AGUM0401-04-1024x770.png)

| No. | name | Description. |
| --- | --- | --- |
| ❶ | SD card slot | SDXC type, UHS-I compatible. |
| ❷ | CONSOLE Port | Used to configure the Edge Gateway with a serial console, connected via a USB Type-C connector. |
| ❸ | DIP switches for configuration | Sets the startup mode of the edge gateway. |
| ❹ | PUSH switch | Used to shut down the Edge Gateway or restore it to factory settings. |
| (in Japanese) ❺ | USB port | Operates as a USB 2.0 host. |
| (in Japanese) ❻ | SIM card slot 0, SIM card slot 1 | Two SIM cards can be inserted in the SIM card slot. The priority level changes depending on the setting. By default, SIM 0 is used. |
| ❼ | power switch | Turns power on and off. |
| (in Japanese) ❽ | AC power input terminal | From left to right: FG, L (ungrounded side), N (grounded side). Screw shape is M4. |

#### Diagonal front view (lid open)

The diagonal frontal configuration is shown below.

![](https://manual.amnimo.com/wp-content/uploads/2024/08/AGUM0401-05-1024x928.png)

| No. | name | Description. |
| --- | --- | --- |
| ❶ | ETH0 port | Standard Ethernet port with Gigabit Ethernet support. |
| ❷ | LAN0, LAN1, LAN2, LAN3 ports (4-port switch) | Standard Ethernet port with Gigabit Ethernet support, PoE (IEEE802.3at) compliant and PoE power supply. |
| ❸ | LED Indicator | PWR: Displays the power supply status. ANT: Displays the antenna status. MOB: Shows the line connection status of the communication module. ST1, ST2, ST3: In combination with other indicators, specific states are displayed. |
| ❹ | RS485 port | Non-isolated type serial communication pins for connection to external devices. |
| (in Japanese) ❺ | D IN | Isolated type digital input terminal for connection to external devices. |
| (in Japanese) ❻ | D OUT | Isolated type digital output terminal for connection to external devices. |

#### three-sided view

A three-view diagram is shown below.

![](https://manual.amnimo.com/wp-content/uploads/2024/09/AXUM0401-06-scaled.jpg)