---
title: interface
description: "This section describes the operation of the \"Interface\" screen. Here, you can check the status of each interface and configure settings. Click \\[Network\\] > \\[Interface\\] on the side menu to open the \"Interface\" screen. ![](https://manual.amnimo.com/wp-content/uploads/2025/09/GU0701-01-1024x495.webp) ## Check the interface ###…"
url: "https://manual.amnimo.com/en/docs/network-gui-en/interface-5/"
updated: "2025-10-03"
category: GUI (FW v3.2.0) / Network (GUI)
---

# interface

This section describes the operation of the "Interface" screen.
Here, you can check the status of each interface and configure settings.

Click \[Network\] > \[Interface\] on the side menu to open the "Interface" screen.

![](https://manual.amnimo.com/wp-content/uploads/2025/09/GU0701-01-1024x495.webp)

## Check the interface

### Displays a list of interface statuses

Click on the "Status" tab to view a list of interface statuses.

![](https://manual.amnimo.com/wp-content/uploads/2025/09/GU0701-02-1024x552.webp)

### Display a list of interface settings

Click on the "Settings" tab to view a list of interface settings.

![](https://manual.amnimo.com/wp-content/uploads/2025/09/GU0701-04-1024x537.webp)

### View interface details

  Click \[...\] to the right of the interface whose details you want to check, and click \[Details\] in the operation menu that appears.

Interface details can be viewed from both the "Status" and "Settings" tabs.

| **Status tab** |
| --- |
| ![](https://manual.amnimo.com/wp-content/uploads/2025/07/GU0701-05.png) |
| **Settings" tab** |
| ![](https://manual.amnimo.com/wp-content/uploads/2025/07/GU0701-05-01.png) |

  You can see the details of the interface.

![](https://manual.amnimo.com/wp-content/uploads/2025/09/GU0701-06-1024x494.webp)

## Add interface settings

### Interface Selection

  On the "Interface Settings" tab, click the "Add New" button.

![](https://manual.amnimo.com/wp-content/uploads/2025/09/GU0701-07-1024x307.webp)

The "Add Interface" screen appears.

  Select the interface.

![](https://manual.amnimo.com/wp-content/uploads/2025/09/GU0701-08-1024x576.webp)

The setting items vary depending on the selected interface.

### Adding eth0

This is how to configure the settings when the eth0 interface is selected.

 **NOTE**

For AI edge gateways, this section should be operated on wan0, not eth0.

   

  Set the basic interface information (1) to (4) and click "Next".

Click on the toggle and select Enable/Disable.

![](https://manual.amnimo.com/wp-content/uploads/2025/09/GU0701-09-1024x288.webp)

② If DHCP (IPv4) is enabled, select the DNS priority and ROUTE metric.

DNS PRIORITY is set in the range 0-99. The default value is 30.
The ROUTE metric is set in the range 0-255. Default value is 30.

![](https://manual.amnimo.com/wp-content/uploads/2025/09/GU0701-09-01-1024x207.webp)

(iii) Enter the fixed IP address (multiple settings are possible by clicking the "Add" button) and set the prefix length.

![](https://manual.amnimo.com/wp-content/uploads/2025/09/GU0701-09-02-1024x100.webp)

(4) If GATEWAY is enabled, set the IP address that will be the default gateway.

![](https://manual.amnimo.com/wp-content/uploads/2025/09/GU0701-09-03-1024x158.webp)

  Configure the advanced settings for the interface and click Next.
\*Because this is an optional field, you can proceed to the next step even if you have not entered any information.

![](https://manual.amnimo.com/wp-content/uploads/2025/09/GU0701-10-1024x510.webp)

  Confirm your entries and click on "Setup".

![](https://manual.amnimo.com/wp-content/uploads/2025/09/GU0701-11-1024x686.webp)

The interface will be added.

### Add br0

This is how to configure the settings when the br0 interface is selected.

  Set the following items (1) to (2) for basic information and click "Next".

Click on the toggle and select Enable/Disable.

![](https://manual.amnimo.com/wp-content/uploads/2025/09/GU0701-12-1024x216.webp)

Set the interface to be used for bridge configuration.

- ［You can add interfaces to be bridged with the "Add New" command.
- The lan registered in the bridge configuration of br cannot be assigned a fixed IP.

![](https://manual.amnimo.com/wp-content/uploads/2025/09/GU0701-12-01-1024x321.webp)

  Set the IP address settings for the interface (1) to (2) and click "Next".

(1) If DHCP (IPv4) is enabled, select the DNS priority and ROUTE metric.

DNS PRIORITY is set in the range 0-99. The default value is 30.
The ROUTE metric is set in the range 0-255. Default value is 30.

![](https://manual.amnimo.com/wp-content/uploads/2025/09/GU0701-13-1024x275.webp)

(ii) Enter the fixed IP address (multiple settings are possible by clicking the "Add" button) and set the prefix length.

![](https://manual.amnimo.com/wp-content/uploads/2025/09/GU0701-13-01-1024x106.webp)

(3) If GATEWAY is enabled, set the IP address that will be the default gateway.

![](https://manual.amnimo.com/wp-content/uploads/2025/09/GU0701-13-02-1024x155.webp)

  Configure the advanced settings for the interface and click Next.
\*Because this is an optional field, you can proceed to the next step even if you have not entered any information.

![](https://manual.amnimo.com/wp-content/uploads/2025/09/GU0701-14-1-1024x358.webp)

  Confirm the information entered and click "Setup".

![](https://manual.amnimo.com/wp-content/uploads/2025/09/GU0701-15-1024x555.webp)

interface will be added.

### Add lan0 to lan3

This is the setting method when the interface from lan0 to lan3 is selected.

  Configure the following basic settings for the interface (1) to (4) and click Next.

Click on the toggle and select Enable/Disable.

![](https://manual.amnimo.com/wp-content/uploads/2025/09/GU0701-16-1024x198.webp)

② If DHCP (IPv4) is enabled, select the DNS priority and ROUTE metric.

DNS PRIORITY is set in the range 0-99. The default value is 30.
The ROUTE metric is set in the range 0-255. Default value is 30.

![](https://manual.amnimo.com/wp-content/uploads/2025/09/GU0701-16-01-1024x215.webp)

(iii) Enter the fixed IP address (multiple settings are possible by clicking the "Add" button) and set the prefix length.

![](https://manual.amnimo.com/wp-content/uploads/2025/09/GU0701-16-02-1024x116.webp)

(4) If GATEWAY is enabled, set the IP address that will be the default gateway.

![](https://manual.amnimo.com/wp-content/uploads/2025/09/GU0701-16-03-1024x143.webp)

  Configure the advanced settings for the interface and click Next.
\*Because this is an optional field, you can proceed to the next step even if you have not entered any information.

![](https://manual.amnimo.com/wp-content/uploads/2025/09/GU0701-17-1024x416.webp)

  Confirm the information entered and click "Setup".

![](https://manual.amnimo.com/wp-content/uploads/2025/09/GU0701-18-1024x585.webp)

### Add ecm0 / rmnet_data0

This is how to set up the ecm0 interface when it is selected.
If you are using a compact router, replace ecm0 with rmnet_data0.

  For basic interface settings, set the following items (1) to (2), and then click Next.

Click on the toggle and select Enable/Disable.

![](https://manual.amnimo.com/wp-content/uploads/2025/09/GU0701-19-1024x206.webp)

Select a mobile line name.

［You can select the name of the mobile line set in \[Network\] - \[Mobile Communication\].

![](https://manual.amnimo.com/wp-content/uploads/2025/09/GU0701-19-01-1024x172.webp)

  Configure the advanced settings for the interface and click Next.
\*Because this is an optional field, you can proceed to the next step even if you have not entered any information.

![](https://manual.amnimo.com/wp-content/uploads/2025/09/GU0701-20-1024x555.webp)

  Confirm the information entered and click "Setup".

![](https://manual.amnimo.com/wp-content/uploads/2025/09/GU0701-21-1024x454.webp)

### Addition of ppp0

This is how to configure the settings when the ppp0 interface is selected.

  For basic interface settings, set the following items (1) to (2), and then click Next.

Click on the toggle and select Enable/Disable.

![](https://manual.amnimo.com/wp-content/uploads/2025/09/GU0701-22-1024x214.webp)

Select the PPP line name.

［The PPP line name set in \[Network\] - \[PPP(PPPoE)\] can be selected.

![](https://manual.amnimo.com/wp-content/uploads/2025/09/GU0701-22-01-1024x166.webp)

(3) If PPPoE (IPv4) is enabled, select the DNS priority and ROUTE metric.

DNS PRIORITY is set in the range 0-99. The default value is 20.
The ROUTE metric is set in the range 0-255. Default value is 20.

![](https://manual.amnimo.com/wp-content/uploads/2025/09/GU0701-22-02-1024x197.webp)

  Configure the advanced settings for the interface and click Next.
\*Because this is an optional field, you can proceed to the next step even if you have not entered any information.

![](https://manual.amnimo.com/wp-content/uploads/2025/09/GU0701-23-1024x440.webp)

  Confirm the information entered and click "Setup".

![](https://manual.amnimo.com/wp-content/uploads/2025/09/GU0701-24-1024x507.webp)

## Editing the interface

Edit the registered interface settings.

   ［ 設定 ］タブをクリックします。

![](https://manual.amnimo.com/wp-content/uploads/2025/09/GU0701-25-1024x223.webp)

  Click \[...\] to the right of the interface whose details you want to check, and click \[Details\] in the operation menu that appears.

![](https://manual.amnimo.com/wp-content/uploads/2025/09/GU0701-26-1024x244.webp)

The "Edit Interface" screen appears.

  Configure the settings in the "Edit Interface" window and click "Configure" to finish editing the interface.

![](https://manual.amnimo.com/wp-content/uploads/2025/09/GU0701-27-1024x632.webp)

Information on interface settings is updated.
Since the IP address will be changed, please access the new URL after the setup is complete.

## Deleting an interface

There are two ways to delete registered interfaces: individually from the interface operation menu, or by selecting multiple targets and then deleting them.

### Delete individual interfaces

This is how to select Delete from the interface's operation menu.

   ［ 設定 ］タブをクリックします。

![](https://manual.amnimo.com/wp-content/uploads/2025/09/GU0701-25-1-1024x223.webp)

  Click \[...\] to the right of the interface you wish to delete and select \[Delete\] from the operation menu that appears.

![](https://manual.amnimo.com/wp-content/uploads/2025/09/GU0701-29-1024x244.webp)

  ［Click the "Delete" button.

![](https://manual.amnimo.com/wp-content/uploads/2025/09/GU0701-30.webp)

The interface is removed.

### Select and delete multiple interfaces

This method is used to delete an interface after checking the check boxes of the interfaces to be deleted. This is useful when deleting multiple interfaces at once. You can also select a single interface to delete.

  ［Click on the SETTINGS tab.

![](https://manual.amnimo.com/wp-content/uploads/2025/09/GU0701-25-2-1024x223.webp)

  Click the checkbox to the left of the DHCP server setting you wish to delete, place a checkmark in the checkbox, and click the \[Delete\] button.

![](https://manual.amnimo.com/wp-content/uploads/2025/09/GU0701-32-1024x333.webp)

  ［Click the "Delete" button.

![](https://manual.amnimo.com/wp-content/uploads/2025/09/GU0701-33.webp)

The interface is removed.