View Categories

Configure interface settings

Configure the interface settings for this product.

Display a list of interface settings #

Displays a list of interface settings.

Click on Advanced Configuration and Control – Interface Settings in the side menu.

The “Interface Settings” screen displays a list of registered interface settings.

NOTE

By clicking tabs such as “Interface” and “Enable/Disable” in the interface settings list, you can sort the interface settings in descending/ascending order for each item.

Adding Interfaces #

Add interface settings.

On the “Interface Settings” screen, click the [ Add New ] button.

The “Add Interface” screen will appear.

Select an interface.

The setting items vary depending on the selected interface.

Adding eth0

This is how to configure the settings when the eth0 interface is selected.

NOTE

For AI edge gateways, this section should operate on wan0, not eth0.

   

Set each item.

DNS優先度は0~99の範囲で設定します。デフォルト値は30です。
ROUTEメトリックは0~255の範囲で設定します。デフォルト値は30です。

For firmware version v2.1.0 or later, the display will show “IP Address” and there will be no check box. if you enter an IP address (you can set more than one by clicking the “Add” button), set the prefix length. if you check GATEWAY, Set the IP address to be the default gateway.

MTU is set in the range of 576 to 9676. Default value is 1500.

When settings are complete, click on “Configure”.

Add br0

This is how to set up the br0 interface when it is selected.

Set each item.

To add, select an interface and click Settings.

DNS優先度は0~99の範囲で設定します。デフォルト値は30です。
ROUTEメトリックは0~255の範囲で設定します。デフォルト値は30です。

  • For firmware version v2.1.0 or later, the display will show “IP address” and there will be no check box.
  • If an IP address (multiple can be set by clicking the “Add” button) is entered, set the prefix length.
  • If GATEWAY is checked, set the IP address that will be the default gateway.

MTU is set in the range of 576 to 9676. Default value is 1500.

Only appears on Edge Gateway (amnimo G series) and IoT Router (amnimo R series) firmware v1.X.X.

When settings are complete, click on “Configure”.

Addition of lan0 to lan3

This is how to configure the settings when lan0 to lan3 interfaces are selected.

Set each item.

DNS優先度は0~99の範囲で設定します。デフォルト値は30です。
ROUTEメトリックは0~255の範囲で設定します。デフォルト値は30です。

MTU is set in the range of 576 to 9676. Default value is 1500.

When settings are complete, click on [ Settings ].

Add ecm0 / rmnet_data0

ecm0のインターフェイスを選択した場合の設定方法です。
コンパクトルーターをご利用の場合は、ecm0をrmnet_data0に読み換えてください。

Set each item.

You can select the mobile line name set in [ Advanced Settings and Control ] – [ Mobile Communication Settings ].

DNS優先度は0~99の範囲で設定します。デフォルト値は30です。
ROUTEメトリックは0~255の範囲で設定します。デフォルト値は30です。

MTU is set in the range of 576 to 9676. Default value is 1500.

Only appears on Edge Gateway (amnimo G series) and IoT Router (amnimo R series) firmware v1.X.X.

When settings are complete, click on “Configure”.

Addition of ppp0

This is how to set up the ppp0 interface when it is selected.

Set each item.

You can select the ppp line name set in [ Advanced Configuration and Control ] – [ PPP (PPPoE) Settings ].

DNS優先度は0~99の範囲で設定します。デフォルト値は20です。
ROUTEメトリックは0~255の範囲で設定します。デフォルト値は20です。

MTU is set in the range of 576 to 9676. The default value is 1454.

When settings are complete, click on “Configure”.

Addition of wlan0 to wlan1

This is how to set the wlan0 to wlan1 interface when selected.

Set each item.
NOTE

When access point mode is selected, be sure to correspond the interface and SSID as follows

  • wlan0: amnimo-2G-xxxxxxxx
  • wlan1: amnimo-5G-xxxxxxxx

Station mode is available only on interface “wlan0”.

MTU is set in the range of 576 to 9676. Default value is 1500.

When settings are complete, click on “Configure”.

Editing the Interface #

Edit the registered interface settings.

On the “Interface Settings” screen, click […] to the right of the interface setting you wish to edit and select [ Edit ] from the operation menu that appears.

The “Edit Interface Settings” screen appears.

Edit the interface settings and click the Settings button.

Information on interface settings is updated.
Since the IP address will be changed, please access the new URL after the setup is complete.

Delete interface #

To delete registered interfaces, you can either delete them individually from the interface operation menu, or you can delete them after selecting all the interfaces you wish to delete.

Delete individual interfaces

This method is to select Delete from the operation menu of the interface.

On the “Interface Settings” screen, click […] to the right of the interface you wish to delete and select [ Delete ] from the operation menu that appears.

The “Confirmation” screen appears.

Click the [ Delete ] button.

interface will be removed.

Selecting and deleting multiple interfaces

This method is used to check the interfaces to be deleted before deleting them. This is useful when deleting multiple interfaces at once. You can also select a single interface to delete.

On the “Interface Settings” screen, click the checkbox to the left of the interface you wish to delete, place a checkmark in the checkbox, and click the [ Delete ] button.

The “Confirmation” screen appears.

Click the [ Delete ] button.

The selected interface is deleted.

Scroll to Top