This section provides a detailed description of each interface on the compact router.
LED #
This section describes the lighting and blinking patterns of the LEDs on the top surface of the compact router.
LED Icon Description #
| LED | Description. |
 | Indicates that the red and green LEDs are off. |
 | Indicates that the red and green LEDs are lit. |
 | Indicates that the red LED is on. |
 | Indicates that the red LED is blinking slowly. (500ms interval) |
 | Indicates that the red LED is blinking at high speed. (125ms interval) |
 | Indicates that the green LED is on. |
 | Indicates that the green LED is blinking slowly. (500ms interval) |
 | Indicates that the green LED is blinking at high speed. (125ms interval) |
Blank columns indicate that the LEDs are not controlled. Any change of state between items has no effect.
LED Status List #
| (data) item | WIFI*1 | MOB | ANT | PWR | remarks | |
| power disconnection (e.g. interrupted power supply) | ||||||
| power-on | | | | | ||
| during startup (of a machine, e.g.) | | | | | ANT, MOB, and WIFI light up repeatedly at 500ms intervals | |
| Initializing by PUSH switch operation | | | | | ANT, MOB, and WIFI flash simultaneously 125ms intervals | |
| Startup error occurred | | |||||
| Power outage | | 125ms interval | ||||
| power disconnected (state) | | |||||
| Antenna Level | ||||||
| unused | | |||||
| usually | | RSSI (-73 dBm or higher) | ||||
| average (e.g. quality) | | 500ms interval RSSI (-74dBm to -83dBm) | ||||
| during (a certain time when one did or is doing something) | | 125ms interval RSSI (-84dBm to -93dBm) | ||||
| slightly weak | | 125ms interval RSSI (-94dBm to -109dBm) | ||||
| weak | | 500ms interval RSSI (-110dBm to -112dBm) | ||||
| outside range | | RSSI (-113 dBm or less) | ||||
| Mobile Connectivity Related | ||||||
| unconnected | | |||||
| connection failure | | |||||
| 2G connection | | 125ms interval | ||||
| 3G Connection | | 500ms interval | ||||
| 4G connection | | |||||
| Wireless LAN function related*1 | ||||||
| Wireless LAN not used | | Access point/station: disabled | ||||
| Wireless LAN connection in progress | | Access point/station: enabled | ||||
| WPS connection in progress | | 500ms interval | ||||
| When WPS operation is disabled | | Lights up for 10 seconds | ||||
| Firmware update in progress | | | | | ANT and MOB flash simultaneously,125ms interval*2 | |
| Firmware update completed | | | | |||
| Firmware update failure | | | | |||
2 The display is the same as during initialization by the PUSH switch.
PUSH switch #
This switch is used to reset the device to the factory default settings or to shift the device to a power-off ready state.
Reset to factory default settings #
Turn on the compact router while holding down the PUSH switch, and release the PUSH switch when the LED indicates that the following initialization is in progress. The various settings will start up with the factory defaults.
| (data) item | WIFI*1 | MOB | ANT | PWR | remarks |
| During initialization by PUSH switch operation | | | | | ANT and MOB blinking simultaneously 125ms interval |
The settings file stored in this device will not be initialized. Therefore, if this operation is performed and then rebooted without writing to the configuration file, the device will start up with the settings that existed before the settings were initialized.
Transition to power-off ready state #
Holding down the PUSH switch for 3 seconds after booting the OS moves the compact router into the power-down ready state.
| (data) item | WIFI*1 | MOB | ANT | PWR | remarks |
| power disconnected (state) | |
If the power-off state continues for a certain period of time, the compact router will be rebooted by Watchdog Timer. This makes it possible to restore power without having to go to the site, even if a command operation (e.g., poweroff command) is mistakenly made remotely to enable power off.
console port #
The console port can be connected with a USB Type-C cable.
The driver for this device must be installed. Please select the driver* for your environment at the following site and follow the instructions to install.
https://amnimo.com/drivers/ac10/
*Compact router series can be used in common.
Console port communication settings
| (data) item | Contents |
| speed | 115200 bps |
| data | 8bit |
| parity | None |
| stop bit | 1 bit |
| flow control | None |
WPS button #
The WPS button enables wireless LAN connection*1,2 through the WPS function.
In the default setting, a compact router with wireless LAN capability acts as an access point. if you press the WPS button for more than 5 seconds, the WIFI LED will start blinking green. After that, you may release the button; it will be waiting for a connection from a station for 60 seconds*2. After 60 seconds, the WIFI LED will return to solid green.
1 If the security mode is changed, the WPS function may not be available.
2 By default, registered station devices are connected to the wlan0 side (2.4GHz).
3 When using the WPS function with the command, the time can be changed.
