This chapter describes the installation procedure for the Edge Gateway Outdoor Type (AG20).
Outline Drawing #
- Weight: approx. 2.8 kg
About power supply connection #
- For power supply connection, connect 100 VAC (L side and N side) and FG (frame ground) as shown above.
- The FG mark and the L side are clearly marked near the connector.
- FG must be connected. Failure to do so may cause accidents or malfunctions.
- Please be very careful not to touch these terminals with metal or your body by mistake.
- After connecting the power supply, work in such a way that the power supply to the equipment can be cut off by installing an NFB (wiring circuit breaker) on the AC100V power line.
- After connecting the power supply, attach terminal caps to the terminal block.
When using a cable gland #
necessities #
| Cable gland (recommended)* sold separately |
|---|
| M7901YR (FGB21L-14B) * For power cable https://www.ip68.jp/products/210_2010_b_products.html |
| M7901YQ (FGA21L-10B-SD) * For Ether cable https://www.ip68.jp/products/210_2015_products.html |
| M7901YY (FGA21L-06B-SD) * For Ether cable https://www.ip68.jp/products/210_2015_products.html |
| M7901YZ (FGA21L-H2-06B-SD) * For Ether cable (when 2 cables are used) https://www.ip68.jp/products/210_8010_products.html |
Installation Instructions #
- To run two Ether cables through one cable gland, use a cable gland for two ports.
- It is not possible to pull out all wiring using only the standard holes. Additional hole fabrication may be required, so please contact your Amnimo sales representative before purchasing.
- Use LAN cables with compatible wire diameters.
See Accessories (sold separately). - When using a cable with RJ-45, use a connector diameter of 14 mm or smaller.
- When using connectors larger than 14 mm, crimp the connectors after passing through the cable gland.
When using PF pipe connectors #
necessities #
| PF pipe connector with verified connection * Not sold by Amnimo |
|---|
| Furukawa Electric: PFS-16KSR-I (IPX5 compliant product) https://www.furukawa.co.jp/eflex/product/plafleky/p_pfbkr.htm |
| Miraikogio: FPK16YPS (IPX7 compliant product) https://www.mirai.co.jp/densetu/pdf-catalog_2021/6000221.pdf |
Installation Instructions #
There is no manufacturer's recommended tightening torque for both PF pipe connectors.
It is not possible to pull out all the wires using only the standard holes. Additional hole machining may be required, so please consult your Amnimo sales representative prior to purchase.
Internal wiring and wiring treatment #
necessities #
| Cable ties for fixing cables (2 pcs. included) *If you need more, please procure and use the following model number. |
|---|
| (Recommended) Takeuchi Kogyo Reuse Snapping Ties RST-130V0 |
Wire connection example #
Since cables are not fixed when using PF Suga, the following procedure can be used to fix cables to prevent stress on connectors and terminal blocks.
About wall installation #
necessities #
| Wall mounting bracket (recommended) * Sold separately |
|---|
| M7901YX (CK-26P) https://www.takachi-el.co.jp/products/CK_BCAP |
Mounting example #
When installing on a wall, use appropriate bolts or screws that can withstand the weight of the unit against a sufficiently strong wall surface. When attaching the metal fittings to the box, use a tightening torque of 1.0 N-m as a guide for installation.
Pole Installation #
necessities #
| Pole mounting bracket (recommended) * Compatible pole/con pillar diameter: 60 to 400 mm M7901YW (SSK-200) https://www.takachi-el.co.jp/products/SSK_BCAP |
| Pole mounting band (recommended) * Pole/con pillar diameter: 60 to 400 mm M7901YU (PKB-10S) https://www.takachi-el.co.jp/products/PKB |
Mounting example #
When attaching metal fittings to the box, use a tightening torque of 1.0 N-m as a guide for installation.
Please refer to the following page from the manufacturer for belt installation instructions.
https://www.takachi-el.co.jp/assets/attachments/images/PKB10S_PKB20S_manual.pdf